Before moving on to the buying guide and the product reviews, how about you have a quick look at 3 of our best products- this will definitely save you quite a lot of time.

The first part of our review is important both for the music enthusiasts just as it is for you if you are looking for your first upgrade. We’ll be having a look at everything there is to know about a component speaker and why you should get one.

Let’s get started right away, shall we?

What makes a component speaker system as good as it is the crossover. The component speaker systems normally have the high frequencies and the low frequencies isolated such that the tweeters get to take care of the highs whereas the woofer gets to handle the low frequencies.

As it turns out, this is what you will expect from just any basic crossover. When it comes to getting the best component speakers under 300, however, your crossover may have separated bands of the high, mid and low frequencies. These different frequency bands feed the different drivers in your sound system i.e. the tweeters, woofers, and subwoofers.

What would happen if you did not have a crossover in your sound system?

Think of a crossover being some kind of audio cop that is able to direct the high frequencies to the tweeters, the midrange to your woofers and the low bass frequencies to your subwoofer. If the crossover is absent, then this will result in a messy sonic jam. Your midrange and subwoofer may end up having too much of the same frequencies such that too high notes may be produced by the latter which was not meant to be the case.

There are basically two types of crossovers- the active ones and the passive ones. The latter does not need any power so that they can be able to filter out the signals as needed. For the active crossovers, however, you'll be needing both power and ground connections. As much as this may seem to be a hassle, the active crossovers will give you more flexibility as well as fine-tuning control over your music.

Active crossover systems

A crossover is considered as an active one only if each of the drivers present has got its own channel of amplification.

The active crossover systems work in such a way that the power present is increased just as is the dynamic range of the frequencies i.e. from the softest sounds all the way to the loudest ones. You will also be able to control the tonal response of your system over the whole audio spectrum.

Active crossover systems will normally be wired in between the receiver and the amp such that all of the unwanted frequencies are eliminated before the amplifier get to boost them and lose energy. This way the amplifier can only be able to focus on the frequencies that it is meant to handle.

For the active crossover systems, there is a volume control on each of the channels so that you can have each of the sounds on the different drivers in balance.

In the best component speakers under 300, you may find other sound processing features such as an equalizer that allows you to easily tweak the sound to your personal preference

As much as the active crossovers may be quite beneficial, the only disadvantage is the connection and setting up of the ground and turn-on connectors. You’ll normally need +12 volts for the ground connectors

Passive crossover systems

The second type of crossover systems are the passive crossovers. Unlike the active alternatives, you do not need to hook these up with a power source to get them working. On the other hand, these are of two types; the component crossovers and the in-line crossovers.

Let’s have a closer look at each, shall we?

Component crossovers

What the passive component crossovers do is that they intercept the signal as it comes from the amp. They are simply a small network of capacitors that are installed near the speakers and they normally will come set at their optimal performance levels.

The best component speakers under 300 is most preferably one with component passive crossovers since the installation is easy.

From the amp, a full range signal will exit after which it is then sent to this passive crossover where the signal is separated with the highs going to the tweeters and the low notes are handled by the woofer. Most o these will normally have a tweeter setting that you can use to turn down if it may seem too loud for the woofer.

Considering that a passive crossover will be filtering the signals that are already simplified, there will be wastage of quite a lot of power. The unwanted signals will then be removed in form of heat.

Something else that you should know about the component crossovers is that since the speakers normally change their impedance levels when playing. This also does alter the crossover point of the passive crossovers which in turn leads to an inconsistent sound definition.

In-line crossovers

The in-line crossovers are normally connected before the amplifier. These normally are cylindrically shaped with the RCA connectors on each end so that all you have to do is plug one into your amplifier inputs.

The in-line crossovers normally ensure that you do not waste time and energy amplifying the signals that you are not interested in. Besides just saving on energy, another benefit that you get from the inline crossovers is that they are easy and inexpensive to install which makes it easy to sharpen the sound quality of your component speaker system.

Sadly, you cannot be able to adjust the frequency of an inline crossover and in addition to this, they work differently with different amps. That being said, if you get yourself a component speaker system with this crossover, you should be certain that it’ll be able to play just exactly as you want it to.

What About the Speaker Materials?

Besides the crossovers, the component speaker systems also consist of the tweeters and the woofer. Let’s have a look at each one of these, shall we?

Woofer material.

On any speaker system, the woofer is what is able to make sure that you get the best lows which in this case is the bass.

It is not every day that you’ll get a speaker that’ll be able to produce low notes exactly as you want it to. regardless of whichever speaker system you are getting, the woofer should best be constructed using material that is stiff and at the same time lightweight.

A good example of a woofer cone material you should look for in the best component speakers under 300 is one made of polypropylene. Even better, this can be a blend of poly and other materials such as mica which gives an even better bass quality due to the fact that it is stiffer.

Though they are not as good as polypropylene and other synthetic materials, woven fabric materials are also an option. At the end of the day, you should go for something that is able to stand up to extreme temperatures and moisture.

Ensure that you get the best highs.

Despite having an outstanding crossover, you owe it to yourself to get the biggest kick of your money. This is why when getting the best component speakers under 300, you should ensure that the tweeter is made of soft materials.

Most preferably, it should also be constructed of poly, textile blends or even silk so that you only get a refined sound quality.

We all have our different tastes and preferences in music, right? Taking this into account, some tweeters are constructed with harder materials. Such will normally have metals, graphite or ceramics which ensure that you get both a bright and snappy high.

Swiveling or pivoting tweeters

Other than just having a perfect set of tweeters on your component speakers, their positioning does matter as well.

You may have the frequencies set right but since their positioning is not correct, you may end up disliking the resulting sound quality. For a better soundstage, the tweeters should best be at ear level or rather aimed towards the ear.

On the contrary, you may be forced to install the tweeters on the doors. This way, you can be able to point them towards your ears and get to enjoy all the low frequencies.

With the tweeters right where you need them to be and the woofer installed correctly, you’ll end up having an outstanding soundstage. Another reason you should take your time when should take your time when shopping for a component speaker system.

Detachable tweeters. 

Other than the swiveling tweeters, there may also be the detachable tweeters, these come in handy if you want to use the tweeters in either a different position or for more convenience, in a different vehicle

The surrounding material

An outstanding cone should be complemented by the best surround. The surround, just as the name implies is the material that's the cone. It indeed does perform a vital role since it is what allows the cone on your woofer to move freely.

Depending on the material you have, the quality of your bass varies. In most cases, for the best component speakers under 300, you’ll get rubber for the surround. This is the best considering overall performance and durability since rubber will be able to move freely hence flexibility is not compromised as the cone will reach its optimal performance. Also, rubber is durable since it is able to stand up quite well to extreme temperatures as well as moisture.

Match up your component speaker to the car.

Match it up with the radio head unit

Getting an outstanding component speaker is ideal, right? What will give you an even better performance and sound experience is getting a speaker system that matches up to your current head unit.

Different head units have got different levels of power handling. These are normally broken down into two categories i.e. low powered and high-powered stereos. The low powered stereo systems normally have at most 15 watts RMS of power per channel. The high-powered stereos, on the other hand, have got 16 watts or more of RMS on each channel.

Considering the power handling of your head unit, you should match the low-powered stereos to high sensitivity component speakers and vice versa.

Here’s a tip for you if you want the best:

If you are getting an entire upgrade to your speaker system, you should first get the best component speakers under 300 and then you can get a head unit that measures up to this.

Ensure the speakers are compatible with your car

Something else you need to greatly consider is that the speakers are 100% compatible with your car. First off, ensure that they are a perfect fit. The woofers, for instance, will be going in the doors hence you should ensure that the mounting depth and width is enough.

Most preferably, it is better if you detach the speakers that are currently installed, measure them after which you can then place your order. You can also look around for the measurements in online sources or contact the manufacturer for more information regarding the measurements.

Installation of component speaker systems.

One of the downsides of component speaker systems is that it may be quite a hassle to have them in place. If you are doing it for the first time, it may be quite difficult if you have a manual as well. The woofers normally go to the doors, the crossover to the dashboard and the tweeters at the most convenient position regarding your preference.

Since you may not be able to do this on your own, you should go ahead and sought out the aid of a professional to have this done for you. Yes, you may be forced to spend a little cash on the installation but you’ll have it done perfectly by an expert.

If you are looking doe the best, then the Focal Access 165 A1 will definitely give you a kick for your money. Let’s take a closer look at what it packs under the hood, shall we?

Considering that the power handling is one of the most important things you ought to consider and also what determines how good or bad a speaker is, it packs an outstanding 60 watts. With such an RMS backed up by a 92-dB sensitivity, it will definitely be outstanding on both the volume and sound quality. The peak power is 120 watts which are quite ideal as well

When it comes to the construction, both the cone and the surround just so happen to be the best. The latter is made of braided glass fiber; considering that this is quite rigid, the bass will be outstanding. The butyl surround, on the other hand, is quite flexible just as it is durable.

For the tweeters, they are aluminum inverted dome tweeters which deliver a wide soundstage and utmost accuracy. Besides this, the aluminum inverted technology gives significance rigidity and at the same time lowers sound distortion.

For the crossover, you’ll be getting a 12/12dB/octave (5kHz) separated Access crossover. This ensures that the sound bands are not compromised whatsoever. With the polypropylene capacitors, you'll be having distortion-free dynamics.

For any audiophile, this set of component speakers will definitely be worth every dime. Let’s find out why, shall we?

Starting with the construction, the Rockford Fosgate T165-S T1 boasts the vertical attach surround technique. This gives the speaker about a 25% more effective cone which is far much better than the others in its class. As a result, you get to have an improved efficiency and output capability

Another unique feature you’ll be getting from this set of component speakers is the new flex fit basket. This utilizes holes and slots which is not the case in the traditional speaker mounting holes. Due to this, it is much easier to fit the speakers in OEM openings and have a more secure fit.

The crossover is one of the parts of a component speaker system that dictates how good or bad the sound quality will be. In order to conveniently separate the mids and the highs, it is able to mimic the musical accuracy with close to perfect accuracy.

For the tweeters, the integrated DDC mounting technology provides the most secure fitting of the same and to make things even better, the installation of the tweeters is quite easy.

For the cone, you’ll be getting the injection-molded carbon fiber polypropylene cone material which, as it turns out, is one of the best since it’s durable just as it is flexible.

There’s nothing as settling as getting the best travel companion, right?

Well, to ensure that you’ll be having a whole new musical experience, we present to you the ESK-165.5. starting with the design quality, this component speaker comes with a water repellent pressed paper cone. Other than being inexpensive and delivering an outstanding bass, it will stand up quite well to moisture. You’ll also be getting a V-cone for the best off-axis response and utmost clarity in mid-high frequency detail

For the power handling, the speakers have got 300 watts for the peak which allows for quite a huge threshold above the 100-Watt RMS power without damaging the speakers.

The surround is butyl rubber hence as far as durability is concerned, you won’t have to worry about damage from extreme temperatures and moisture. Besides just being durable, the butyl rubber is quite flexible which makes it quite ideal when it comes to the production of quality bass.

A neodymium magnet is one of the ideal types of magnets as far as getting outstanding highs on tweeters is concerned, right? Well, this one’s got just that- utmost strength and detailed highs.

Moving on with our list, we’ve got the Alpine SPR-60C coming fourth. Let’s have a closer look at what it packs under the hood, shall we?

The power handling is one of the most important things when it comes to sound production, right? To ensure that you get to have the best listening experience, this component speaker has got a peak power of 330W and an RMS of 110W. Both of these will greatly contribute to ensuring that you get close to perfect sound quality.

For the tweeters, you’ll be getting them in flush mountable enclosures. These allow the tweeters to pivot for the sake of front stage imaging. the backplate holds the tweeters in place and uses plastic tabs hence you should be careful not to break these.

For the cone, the Alpine SPR-60C has got the hybrid layered-pulp cone. The best thing about this is that it cuts down on the overall price of the speakers without compromising the sound quality whatsoever.

Wrapping things up, you’ll be getting an outstanding 4 ohms on the impedance and backed up by the 110 watts of RMS power, this is just the perfect speaker for everyone.

We’re nearly past halfway done with our review and one thing’s for sure- the JBL GTO8608C is a component speaker like no other and will definitely give you a bang for your buck. Here’s what you ought to get from it.

Starting with the construction design, this component speaker has got a rubber surround around the cone. This ensures that there is utmost flexibility and in addition to this, the surround is quite durable as well since it will hardly be affected by extreme temperatures and moisture.

For the tweeters, you get a Mylar-tweeter with a large voice coil which is what you’ll also get in high-end home audio speakers. The benefit of having this is that it is both lightweight and not shortchanged on the strength. Besides being strong, it simultaneously has increased power handling and reduced distortions at high output levels.

The woofer does have the JBL-exclusive Plus one cone technology that gives the cone more surface area as compared to other models. By covering a larger surface area, the speaker provides a higher efficiency as well as a better bass response.

So as to ensure that all the sound waves go exactly where they are meant to go to, you’ll be getting a computer-optimized outboard crossover. This simply ensures that the high frequencies get to the tweeters and the lows and mids go to the woofer.

Also:

For the installation, the JBL speaker comes with the I-mount tweeter system. This makes it quite easy for you to flush-mount or surface mount the tweeter. Other than just making it easy to mount the tweeters, the I-mount also does make it simple for you to angle the tweeters and lock them at the most suitable angle for optimum imaging and response.

So far so good, we’re past halfway done with our product listing and we are doing good so far. Let’s take a look at the 165 V20 – Focal.

First off, besides from being manufactured by one of the best brands, this component speaker boasts to have quite an outstanding power handling. The 20-watt RMS power and 140W for the peak power guarantees an outstanding bass as far as quality music is concerned.

Moving on to the tweeters, you’ll be getting the aluminum/magnesium inverted dome tweeters. This kind of tweeter is renowned for producing an accurate sound and in addition to this, you get to have a deep soundstage for the best experience.

For the crossovers, you’ll be getting a 2-way separate crossover. Each of these handles each pair of the woofer and tweeters. Either is 6/12 dB/Oct (4.5khz) for the best sound band isolation.

With this JL audio 7.7” coaxial speaker system, you’ll definitely be getting the best deal there possibly is. For starters, it’s an outstanding 7.7” coaxial speaker system and since a speaker is as good as its size, this one will not compromise on the sound whatsoever.

Despite just being large in size, the speaker comes with a power handling of 70 watts. This ensures that you get an outstanding bass. Other than just having an outstanding power handling, this set of component speakers has got a 4-ohm impedance. Working hand in hand with the RMS power, it is definitely the best choice if you’re all about the details.

As for the construction, the cone is injection-molded mica-filled polypropylene cone. This is engineered with a dust cap for a smooth upper-end response.

As for the surround, you’ll be getting a synthetic optimized rubber surround. Besides just being flexible, this I known to be outstanding for marine duty UV-resistance.

The tweeters also are formulated to withstand UV and salt-spray exposure. Other than just this, they just so happen to have a silk dome which, as far as quality and detailed highs are concerned, are just the best.

For an outstanding bass, the speaker has been constructed with neodymium magnet. An added bonus to the construction is that you’ll be getting a permanent grille that ensures optimal high-frequency.

If you want to have possibly the biggest kick for your buck, then you should definitely consider taking a look at this set of speakers.

Here’s what it packs under the hood:

First off, for the power handling, you get an outstanding RMS power of 150 watts. This is unlike any other RMS power you can get from a component speaker system since it allows you to play quite a booming and clear bass.

For the impedance, you’ll be getting 2 ohms which, working hand in hand with the RMS power guarantee utmost clarity on the sound.

Being a 2-way component speaker system, you’ll be getting two tweeters and two woofers. Shifting our focus to the tweeters, it’s worth pointing out that not only will you be getting two of these each of which will play outstanding highs, but you’ll get the mounting hardware too. It’ll definitely be no hassle to set up your tweeters.

Looking for the best component speakers under 300, then the Infinity Kappa 60.11CS will definitely be worth every penny.

First off, starting with the power handling, the component speaker has a peak power handling of 540 watts per pair and 270 watts on each speaker. For the RMS, you’ll be getting 180 watts per pair and 90 watts on each of the speakers.

The impedance of the speakers is 2 ohms which, working hand in hand with the power capabilities of the speakers will definitely produce the best highs, mids, and lows.

As for the sensitivity, this set of component speakers has got 93 decibels of this. With this, coupled up with the power handling capability of the speaker, you won’t be needing too much power to have a decent bass and at high volume.

For the cone, you’ll be getting a carbon injected glass fiber cone material; the plus one cone technology offers more cone surface area than you’ll get on any other ordinary woofer.

Around the cone is a rubber surround. This gives the cone utmost flexibility making it the best in the production of quality bass. In addition to being flexible, the rubber will stand up quite well to extreme temperatures as well as moisture hence you get to use it for quite some time.

Summing up our review, we have another outstanding product from Rockford- the Rockford Fosgate T1650-S. let’s have a look at what it packs under the hood, shall we?

First off, the power handling is just outstanding. It has an RMS of 80 watts and for the peak, you’ll be getting as much as 160 watts. Working with these, you'll definitely enjoy the best highs, lows, and mids.

For the sensitivity, each pair has got 88dB of these. Considering that you’ll be working with 80 watts of continuous power and 160 watts on the peak, you won’t have to worry about using too much power in order to achieve higher volumes in your music.

The nominal impedance of the speaker system is 4 ohms. This, as it turns out, will come in handy quite well since you’ll be getting acute accuracy and clarity on the sound considering that the power handling is outstanding as well.

The speaker system also includes an external crossover which isolates the high frequencies to the tweeters and the lows, on the other hand, are handled by the woofer. This way, you end up with the best soundstage and musical experience.

Coming to the end of our review, we can concur that there is no shortcut when it comes to getting an ideal set of component speakers. You need to be ready to invest both the time and money needed to get the best.

Just as it is the case when shopping for any vehicle accessory, it is quite important that you pay attention to details for the component speaker systems. The tweeter and woofer construction should be of good quality and the crossover as well ought to be ideal.

All in all, music preference is entirely a personal taste and you owe it to yourself to get the best component speaker. With 2018’s top 10, you should definitely get the best component speaker.

To save you the hassle of reading all through, you could have a quick look at 3 of our best speakers.

Enter your texWith the component speakers, you have the woofer and the tweeters as separate drivers. To make things even better, you could introduce a crossover so that each of them performs better individually.

Have the tweeters as close to ear level as possible. For the best sound output from the tweeters it is best that you have them installed high up. 

Higher frequencies are more directional as compared to the low frequencies hence you’ll be able to feel the optimal performance of the tweeters if they are at ear level best.

As much as you’ll need the tweeters up, they should also be as close to the woofer as they can be, if otherwise, the different frequencies from the two may reach your ear at different times.

Crossovers: for those who have no idea what the crossovers are, think of them as an audio cop for either your radio or amp. With the external crossovers, the frequencies that are above a given point will go to the tweeters and those below this point automatically go to the woofer. You could have them tucked in your door or dashboard.

With the crossover and the tweeters in position, you should now have the woofers in place. It’s not hard to mount these, the component woofers can be placed in your automobile’s factory locations and most likely in the doors. 

This should be free from any physical tweeter interference since with the more resonant low frequencies, there will be a better foundation for detailed highs.

Merits of having component speakers.

With component speakers in your car, you’ll get a better, higher and wider sound. Nonetheless, here are some of the 3 major benefits of having components speakers.

An outstanding tonal clarity.

This is where you’ll really get to appreciate the crossover network since this frees up the woofer and tweeter to focus more on their assigned frequencies.

With a defined crossover point, each driver is kept from straining and trying to play the limits that it is not meant to handle. It just so happens that with the new boost in sound clarity, you will be surprised by how much different the music you are used to listening to sounds now.

Better sound visualization.

There’s nothing as good as the experience of separating all the sounds you listen to and getting a whole new visualization. With the raised sound stage, the clarity in tone, frequency and stereo separation, you’ll feel like you are enjoying the moment as it happened or rather you’ll get the concert experience.

Better soundstage.

Whereas the factory installed coaxial speakers make the sound seem to be hovering below you, installing component speakers will definitely give you a whole new experience. With the tweeters elevated to the dash, the sail or ‘A’ panels of your vehicle, you’ll have the stage raised hence you get the illusion of the music sounding like it is right in front of you.

Amplifiers make things even better

The best thing about component systems is that they are made to handle higher amounts of power as compared to coaxial counterparts of the same brand. If you have an external amplifier, they’ll definitely sound better.

Note: if you aren’t planning to have an onboard amp added, ensure the component speakers are meant to perform at their best only on deck power.t here...

Moving on to the second section of our review, let’s have a look at 15 of the best component speakers you could get for your money.

Starting us off on our list is the Pioneer TS-165P. well, one thing that’s guaranteed with this component speaker is that if you are on a budget, then it is definitely something worth having a look at.

Starting with the design, it comes with a carbon graphite IMPP interlaced Aramid Fiber Cone. Other than being quite durable, the carbon fiber cone gives the speaker enough room for movement so that you’ll end up with the best sound quality.

As for the surround, it comes with the lightweight Eastic Polymer. Besides being highly sensitive so as to allow for the best sound quality, the surround will also be able to stand up to high temperatures, cold conditions as well as moisture.

Frequently asked questions

Q: how many speakers do I get in one set?

A: 2 pairs hence 4 speakers in total

Q: how is the bass quality on the speakers

A: even though they sound good, they give a better high than the bass

Q: what is the size of the speaker?

A: 6 by 9 inches

As far as sound quality is concerned, the design and construction of every inch on this speaker is meant to make things sound as best as they could.

Starting with the surround, it is made of rubber. Rubber is one of the best materials you could have as a surround on your speaker since not only does it allow enough room for vibration but it also stands up to high temperature, cold and doesn’t give in to moisture contact.

The 92dB sensitivity on the other hand ensures that you get a high sound quality and at the lowest power consumption.

As for the coil, it is the poly injection type (polyurethane to be specific). This is a resilient, flexible as well as durable manufactured material that allows for maximum flexibility which in the end will give you the best sounding speakers for the longest time possible.

With the mylar tweeters, there is a wide variance of the sound modifications and channel handling. As compared to the paper cones, the durability on mylar is better since the cone material is plastic poly which neither rips nor tears easily.

Frequently asked questions

Q: do the tweeters come with a flush mount cup?

A: yes, they do.

Q: will they easily blow out?

A: no, the sound is excellent

Q: how many speakers do I get out of the box?

A: 2 speakers and 2 tweeters

As far as power is concerned, theNakamichi NSE-60S, being a component speaker has one of the best. Considering getting component speakers is all about having the best sound quality and music experience, the 30 watts of RMS power and 400 watts of peak power will allow you to listen to almost any music genre and have the best experience.

The cone is made out of polypropene which just so happens to be one of the best you could get on a speaker. This allows for enough speaker movement hence giving you the best sound at the end of the day.

With the rubber surround, not only do you enjoy durability when it comes to standing up to extreme cold or temperatures, but it also turns out to be thebest surround when it comes to giving the speaker enough room for movement hence the best sound quality.

Frequently asked questions

Q: what are the dimensions of the package?

A:16.5 x 10.2 x 4.2 inches

Q: how is the power handling of the speaker system?

A: has an RMS of 30 watts and a peak of 400 watts

Q: how is the sensitivity of the speaker system?

A:comes with 89dB. This gives you a better sound quality at low power consumption.

Starting with the design, the 2 Kicker DS62 comes with UV-treated surrounds which will give you a precise linear excursion and in addition to this you end up getting the finest sound. The component speaker also features a heavy-duty motor structure and extended voice coil woofer technology for an outstanding performance and better music realism.

Something else to point out about the sound is that the speaker comes with titanium-dome tweeters with an oversized voice coil. This is able to deliver an outstanding definition and can also be mounted in 3 different ways for more convenience.

The mounting depth of the speaker is also smaller hence it will be easier for you to upgrade on your vehicle’s doors or in the kick stands.

The external two crossover network features 3-position tweeter levels that allow or dialing higher frequencies.

Frequently asked questions

Q: does it come with tweeters?

A: yes, it does.

Q: will it come with other mounting hardware

A: yes, it has these out of the box.

Q: how is the power handling?

A: the RMS is 60 watts per speaker and 120 per pair while the peak is 120 watts per speaker and 240 per pair.

As far as getting a budget component speaker is concerned, the infinity Primus will definitely blow your mind. Well, let’s have a look at what it’s got in store for us.

Power handling: the peak is 320 watts for every pair and 160 watts for each. As for the RMS, it is an outstanding 160 watts per pair and each of them has 80 watts. With such a power handling, you’ll get to play your favorite tunes without the sound getting distorted or damaging the speaker.

The surround is the hi-roll rubber type. Rubber just so happens to be one of the best materials you could have on your surround since it is able to stand up to high temperatures, extreme cold and moisture as well.

Installation of the tweeters is made easier since out of the box, you get starfish mounting brackets. These can be used to install the tweeters in the factory locations.

Frequently asked questions

Q: are the crossovers passive or active?

A: it comes with a 6dB octave HP/LP passive crossover.

Q: does it come with mounting hardware such as screws and brackets?

A: yes, it does.

Q: are there 2 of the 6 ½ and 2 tweeters?

A: yes, these are what you get out of the box.

Starting with the design, the Infinity Reference 6030c has got a rubber surround. With this, you end up with the best bass output, even better, it allows enough vibration room for the speaker, has a higher efficiency and just so happens to be the best when it comes to standing up to extreme temperatures and moisture.

With the edge-driven textile dome tweeters offer an increased power handling and in addition to this, the distortion is reduced at high output levels.

The speakers come with a laboratory-optimized passive crossover networks that also have got tweeter level adjustment. This ensures that you get the best music imaging as well as an outstanding sound visualization.

The plus one woofer cones on the speaker has got more surface area as compared to the competing models of the same size. In the long run, you end up with an increased bass output and a higher efficiency.

Frequently asked questions

Q: do they need an amp or can I install them with the factory radio?

A: you can install them without an amp

Q: does it come in a pair?

A: yes, it does, and the sound is great

Q: what is the cut-out diameter for the tweeters?

A: this is 52mm. they are however small enough to fit anywhere and have a lot of hardware mounting options.

As far as component speaker are concerned, be sure to have your mind blown by the Polk Audio DB6501. For starters, the adaptor rings make it easy to be able to fit the Polk Audio DB6501 in both the 6 ½ and 6 ¾ inch applications.

The woofers feature a polymer/mica composite cone. This composite design will give you a better bass and outstanding sound quality in general as well as utmost durability.

Besides the outstanding cone on the woofers, they also have a butyl rubber surround. This just so happens to be the best possible surround material you could get on a woofer since not only does it allow enough room for speaker movement but it is durable to extreme temperatures as well as moisture.

As for the tweeters, they are the 25mm liquid-cooled silk/polymer composite dome with a neodymium magnet that gives you a high, clear and detailed sound.

Frequently asked questions

Q: is an amp necessary to run these speakers?

A:it is not necessary but would definitely sound better.

Q: how do I connect the cross overs?

A: there is an in and out. All you have to do is connect the speakers to the crossovers and use your existing stock speaker wires to the crossover.

Q: how many woofers, crossovers and tweeters do I get?

A: you get 2 tweeters, 2 woofers and 2 crossovers.

Considering all the reasons there are for you to get a component speaker system for your car, one thing that’s for sure is that getting what is going to offer you what you really want is no easy task. Well, let’s have a look at what it’s got in store for us…

The cone, for starters, is the glass fiber type. This one turns out to be the best when it comes to giving you an acute accuracy in mid-range sounds as well as resistance to wear and tear and also standing up to extreme temperatures.

As for the surround, the CT Sounds Meso comes with the NBR rubber surround. Besides being durable, it also allows enough room for utmost speaker vibration so that you end up with the best sound quality.

With the cast aluminum basket, you get both a lightweight and strong design on your speaker. You therefore do not have to worry about looking for a replacement real soon.

Frequently asked questions

Q: is this a 3-way component set?

A: no, it’s a pair of 2 6.5-inch woofer and 2 1-inch tweeters

Q: what gauge wires do these terminals take?

A: it can take up to 12-gauge wires. The lower the number the thicker the cable.

Q: what is the cut hole for the 6.5 inch?

A: the 6.5” coax is 5.6” and the component is 5.8”

We’re now already past halfway on our list. Let’s see what the CT Sounds Strato packs under the hood then, shall we?

First of all, the included crossover network has got a crossover point of 3.5kHz. this ensures that the high frequencies are only received by the 19mm silk dome tweeters. Speaking of the tweeters, the fact that they are silk dome gives them utmost clarity and no sound distortion at all.

The magnet is the 14oz ferrite magnet which pushes these speakers to their limits so that you only end up with the best tonal accuracy.

As for the cone, it is the IMPP design. This is made when polypropene is injected as a foam within a speaker mold so that the retained air bubbles make it lightweight and at the same time, strength is not compromised.

As for the surround, it is the NBR rubber. This is able to stand up to extreme temperatures and moisture as well, more so, it gives the speaker enough room for vibration.

Frequently asked questions

Q: can the speakers mount to the woofer?

A: no, they can’t mount to the woofer

Q:how do they sound on a factory head unit?

A: the sound is awesome on a factory stereo system.

Q: does the 1 qty come in a pair?

A: yes, it does

10^th on our top 15 list of 2017 is the MB Quart XC1-216. Truth be told, this surely is a game changer when it comes to upgrading your stereo system.

Here’s what its got in store for you…

Power handling: when it comes to power handling, you get an outstanding peak of 180 watts per set and 90 watts on each side. As for the RMS, each set has got 90 watts while the individual sides have 45 watts each.

This, in the long run allow you to play a number of tunes at a reasonably high volume without sound distortion or damage. For the best performance however, it is recommended that you maintain the minimum power at 10-75 watts RMS.

The component speaker features a 25mm pure titanium dome tweeter with a silk surround mated to a 20mm KSV voice coil. This combination ends up giving you a high frequency extension.

The midrange has got strong injection molded cones and the baskets are made from a glass fiber reinforced PA66 composite to eliminate any unwanted sound from the music.

Frequently asked questions

Q: is the price for 2 speakers or 4 speakers?

A: the price is for the4 component set.

Q: how is the sound quality?

A: if you want crystal clear mids and highs, you should get these.

Q: will I need an amp?

A: you don’t have to get one but for a better sound, you should

If you are willing to push your limits and spend on your stereo system, then you should definitely consider checking out the Alpine SPR-60C.

Starting with the sensitivity, the Alpine SPR-60C has got 87dB. If you’re looking for a decent sound quality, this component speaker will definitely do you justice. As for the power rating, it is rated at220 watts per set and 110 watts on each side; the peak on the other hand is 660 watts per set and 330 watts on each side.

Another outstanding feature about the speaker set is that on the crossover, you can be able to change the dB settings on the tweeters so that the sound (especially the treble will not be irritating at all).

Mounting won’t be a problem. When it comes to the installation of both the crossovers and the speakers, they can easily be placed on the front doors of most cars.

Frequently asked questions

Q: which amp should I use on these speakers?

A: a 300 watt or a 400-watt amp should do.

Q: what is the hole saw size for the tweeters?

A: they are 2” holes.

Q: does it come with adapter plates to fit 6×8 holes?

A: yes, it does.

As far as getting an outstanding sound is concerned, the Focal P165V15 will give you nothing but the best. Starting with the power handling, it has got an RMS power handling of 80 watts and the peak power is an outstanding 160 watts.

To give you the best sound, the cone is made of polyglass. Other than delivering a decent bass quality above all else, the overall sound quality you get from the speaker is at its best. With polyglass, the strength of the cone is also better as compared to polypropene which you’d get on most speakers.

One other important feature on the speaker construction is that it comes with a butyl surround. This, being rubber is tolerant to extreme temperatures as well as moisture.

To make the sounds even more detailed, the tweeters have an inverted aluminum dome. This creates a broader sound stage. The tweeters also have a neodymium magnet so as to produce a strong magnetic field for all the voice coils and at the same time maintain the compact dimensions of the tweeter.

Frequently asked questions

Q: how big are the tweeters?

A: the frame diameter is 1.886”, the cutout diameter is 1.677”, the width is 1.887” 1.894” and the surface depth is 1.887” 2.865”

Q: what are the switches on the crossover for?

A: they are for tweeter adjustment. You can use these to set the tweeter as per your preference

Q: which wires should I use to hook them up?

A: you need a 12-16-gauge pure speaker cable to do this.

We’re almost done with our list now. Let’s have a look at what the Focal Access 165 A1 packs under the hood.

Starting with the design, the Focal Access 165 A1 features a butyl rubber surround. Rubber just so happens to be one of the best materials you could use as a surround since it is able to stand up to both moisture and extreme temperatures and will give the speaker enough room for movement.

As for the tweeters, they boast the inverted dome tweeter technology. This offers outstanding rigidity and lowers any distortions on the sound.

The crossovers:

The 12/12dB/octave (5kHz) separated Access crossoverhas got polypropene capacitors which give the speaker both high and distortion-free dynamics. You can also be able to refine the tuning on the tweeters in all locations.

Frequently asked questions

Q: does it come with grills?

A: yes, it does

Q: does the dual fiber glass give more sp than poly glass cone?

A:yes, it does

Q: what is the RMS? Can a 4 channel 75-watt amp do them justice?

A: they are rated at 50 watts RMS hence 75 is more than enough.

Second last on our list is the ESK-165.5. as far as getting a component speaker is concerned, this one just so happens to be one of the few that will give you the biggest bang for your money.

Let’s have a look at what it’s got in store for us…

The design:

With the Vcone technology, you’ll have the best off-axis response and in addition to this, there is a clear mid-high frequency detail. The paper cone on the other hand is water-repellent hence you don’t have to worry about contact with moisture.

As for the surround, this is made out of butyl rubber which just so happens to be one of the most durable and flexible surrounds you could get.

Power handling:

When it comes to the peak and RMS ratings, the ESK-165.5 boasts to have as much as 100 watts of RMS power and 300 watts of peak power.

Frequently asked questions

Q: do the tweeters mount inside the speaker

A: no, you’d have to make a bracket to mount in the speaker

Q: what is the RMS per speaker?

A: it is recommended that you feed them with 100 watts of RMS

Q: do they come with a warranty?

A:yes, they do, but it depends on which seller you are purchasing them from.

Coming final on our list is the Polk Audio DB6502. Being one of the high-end component speakers you could get in the market today, let’s have a look at what it’s got under the hood…

For starters, if you want the most durable, this one’s definitely it. it has been tested for dirt and water resistance as well as waterproof inner and outer surrounds.

The cone, being made out of polypropene just so happens to be one of the best when it comes to giving a clear sound. One more thing that’s worth pointing out about the cone is that it is UV tolerant meaning that you won’t have to worry about it being damaged by UV light.

Power rating. As for the power rating, the Polk Audio DB6502 has got an outstanding 300 watts of peak power and in addition to this, the RMS is 100 watts. These make it an outstanding choice if you are so much into loud music.

The speakers also do feature non-resonant materials. Simply put, these make it possible for you to have extremely clear highs, mids and lows regardless of what you are listening to. All this can be credited to the patented Dynamic Balance technology.

Frequently asked questions

Q: how do I adjust the crossovers?

A: there is the decibel switch when you pop open the crossover.

Q: do I need an amp to use them?

A: not necessarily but it would give a better sound quality.

Q: how is the surround on the speakers?

A: it is durable and both the inner and outer surrounds are water resistant.